Connect all the miners to the USB-hub, then connect the USB-hub to the USB-port of your computer.First, refer to the above, run each miner individually to confirm each miner works well.Here is the guide for how to mine with 2 miners with a USB-hub. METHOD 2: Use a USB-hub (Which is connected to your PC) to connect all the miners and run the miners.METHOD 1: Connect all the miners to the USB port of your computer, and run them together.There are two ways to run more than one miners together: Then it should be working as in the following picture:.bat file is as the following, please change the “pool_address_1, pool_address_2, miner_account_1, miner_account_2” to yours.Ĭgminer.exe -bmsc-options 115200:0.57 -o pool_address_1 -u miner_account_1 -o pool_address_2 -u miner_account_2 -bmsc-voltage 0800 -bmsc-freq 1286 Use the notepad to open it and modify it. Connect the miner to the USB port of your PC via data cord again, and please note: insert in the same USB port as before.Pull out the USB cord of the miner and power off the miner.After the replace work done, close zadig.Choose “Options->List all drivers”, and then in the pull-down list (as shown in Picture 1(see below)), there are one “CP2102 USB to UART Bridge Controller”, choose it and click “Replace Driver”. Run the zadig_v2.0.1.exe in the software package you download.If your PC shows up “setting up the driver”, wait it to finish.Connect the miner to the USB port of your PC.After you connect the PSU, the fan of the miner should be working. Set up the driver “CP210x_VCP_Windows”(For 32bit OS, please install “CP210xVCPInstaller_x86.exe” for 64bit OS, please install “CP210xVCPInstaller_圆4.exe”).Download the driver: CP210x USB to UART Bridge VCP Drivers.Connect the miner to the USB port of your PC with the data cord.If you haven’t bought our PSU package: you need to connect the miner to the 6pin cable of your ATX PSU by the “6pin to DC” cord included in the package.If you have bought the PSU package in our store: please connect the PSU to the miner directly, then, connect the PSU to the socket on the wall with the power cord you prepared.If you haven’t bought the PSU package in our store, please prepare a ATX PSU (>= 100w, with 6pin x 1) by yourself.If you have bought the PSU package in our store, there is no power cord included, you need to prepare a power cord for the miner.In this tutorial, we will demonstrate the setting-up for Antminer U3(63GH 63w) bitcoin miner. THen I BLACKLIST THOSE TWO.Antminer U3 is a bitcoin miner with petite size and it’s a good option for beginners. So I Disable two of those first 5 with the USB Menu in CGMiner. OK, Now what? one is running 5 U3's terribly, and the other is whining about all the devices being busy, or not there, etc. I HAVE TWO EXPLORER WINDOWS OPEN AT ONCE. So I start moving things to a different directory, to "start all over" and while doing this, I notice. Well, I bought FIVE of these, and I am determined. I could run ANY THREE at a time, but 4 would start the errors and crashes all over again. I could get them all to run in 2's or 3's, but with 4 or 5 they would hash at ridiculously low speeds, and crash to zombie a LOT. I want all 5 U3 Miners running normally at once on the same machine! I tried new power supplies, new cables, new software.NOTHING WORKED. I did the Zadig thing, a million times, can do it in the sauna, while reading bad Hungarian poetry.Īll my devices are running the right drivers. I have been trying for MONTHS to get all five of these to all work at the same time without ZOMBIEĪnd ERRORS that make the whole process a waste of time.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |